Sheet Doors

Commonly referred to as “Mini Storage” doors, sheet doors are made up of a continuous sheet that rolls up into a coil. If you have a smaller door opening or mini storage facility R&S can provide sheet doors by Dbci. For an economical value the sheet door is an easy way to secure a garage opening. Click Here to request more information.

Color Chart

sheet door color chart.pdf

Mini Door Series 650

sheet door 650.pdf

Description:

The 650 Series is the premium door for easy operation and maintenance. Features shielded steel radial bearings on both support brackets. DBCi tension bracket allows you to easily, quickly, and safely adjust tension on your door. Rain lip note: For proper exterior door installation, a 11/2″ deep rain lip must be formed in the concrete slab, extending a minimum of 31/2″ from the interior face of the jamb.

Curtain

  • 26-gauge grade E hard steel, 5/8″ deep ribbed corrugation
  • 20 standard colors – special colors upon request
  • Wash coat over primer interior side
  • The Weather X system is recognized for its remarkable color and gloss retention as well as its superior chalk resistance
  • The Weather X system allows the product to endure the physical abuses of fabrication, transit and construction while minimizing cracking
  • 25 year film integrity warranty – up to 25-year chalk and fade
  • Stainless steel latch. 2 padlock style, cylinder style, or with the new cast zinc Apex latch. All latches accept double locks and 7/16″ shackles.

Bottom Bar

  • 6063-T6 aluminum extrusion
  • 1 1/2 ” x 11/2″ x 11-gauge galvanized angles to provide structural stability, security, and increase windloads
  • Bulb astragal – replaceable vinyl weather seal

Axle Assembly

  • 1 5/16″ O.D. steel axle 14-gauge
  • Oil tempered torsion springs
  • 18-gauge 9.5″ drums
  • Fully accessible springs for inspection

Guides

  • 18-gauge galvanized steel guides
  • Pre-punched holes for anchors, slide latch, and bracket attachment
  • Polyethylene guide strips provide easy, quiet operation
  • Pre-punched holes for head stop attachment

Hardware

  • 12 gauge head stops have slotted mounting holes for proper attachment
  • 14 gauge galvanized steel handles
  • 12 gauge tension bracket is coined for additional strength with shielded radial bearings for smooth operation. Worm gear adjusting design allows unlimited adjusting positions.
  • 12 gauge bearing bracket left side

Options

Insulation (Series 651)
Windload (Series 700)
Top and side draft stop
Comes standard with our new easy to use tension bracket

Light Duty Commercial Series 2000

sheet door 2000.pdf

Description:

Series 2000 is designed for frequent usage requirements
Light duty applications for frequent usage including warehouse, freight terminal and industrial warehouse
Utilizes 12″ drums
Limited maximum size of 12′ x 18′


Curtain

  • 26-gauge galvanized
  • Grade E hard steel
  • Deep ribbed corrugation
  • 20 standard colors – special colors upon request with upcharge
  • Siliconized polyester Weather X paint over prime coat
  • Wash coat over primer interior side
  • 25-year film integrity warranty – up to 20-year chalk and fade
  • Improved flexible wear strips
  • 4″ of curtain add


Bottom Bar

  • 6063-T6 aluminum extrusion
  • 2″ x 11/2″ galvanized angles
  • Bulb astrigal
  • Stainless steel nuts and bolts


Axle/Torque Tube

  • 1 5/16″ O.D. steel axle, 14-gauge
  • Oil tempered torsion springs
  • 16-gauge drums 12″ diameter galvanized
  • Steel ball bearings
  • Full top sheet 26-gauge galvanized


Guides

  • 14-gauge galvanized
  • Polyethylene wear strip
  • Bolt on head stop 1/4″ plate steel
  • 15/8″ deep engagement
  • Pre punched for lock and attachment screws


Hardware

  • 13-gauge saddle clamps
  • 10-gauge slide locks 2 per door
  • 16-gauge step plate 2 per door
  • 1/4″ steel welded angle T-bracket


Options

Insulation Series 2250
Chain hoist 4:1 reduction
Vision panels (17″ x 5″)
Top draft stop
Hood
Steel mounting plates
Electric operator

Frames and Panel Systems

sheet door frames and panels.pdf

Roll-Up Frames

The roll-up frame is a non-load bearing interior hallway jamb for attaching DBCi roll-up doors. The strong, flush 20-gauge frame is used in both corrugated and flush hallway systems and is available in glossy white or Galvalume. Includes base plates, back plates and top channel.

20-gauge
Siliconized polyester Weather X paint finish
Press break construction for variable sizes
20-gauge back plate for mounting header/filler panel and roll up door bracket
20-gauge base plate that mounts roll-up frame to floor
#8 x 1/2″ glossy white self drilling screws

Flush Header Panel

The flush header panel attractively closes the gap between the top of the roll up door and the top of the hallway system. The flush header panel with roll up frames creates a clean flush hallway. The flush glossy white header panel reflects light that provides a brighter interior.

For interior hallway systems
Single piece construction
20-gauge
Siliconized polyester Weather X glossy white paint finish
#8 x 1/2″ white self drilling screws

Filler Panel

Filler panels are an economical way to close the gap between the top of the opening and the roof. Filler panels are used in interior and exterior applications. The painted 26-gauge panels match the corrugation of the door. Panels are framed in at the sides, top and bottom with matching support channels and angles can be manufactured to match the color of the rollup door or contrasting color.

26-gauge panel, support channel, and angles
20 standard colors in siliconized polyester Weather X paint
For interior and exterior use
#8 x 1/2″ self drilling screws available in similar colors